3003 Aluminium Coils
Likhoele tsa aluminium tse 3003 ke tsa mofuta oa AL-Mn alloy e ka bang 10% e matla ho feta alloy 1100. Lipampiri tsa aluminium tse 3003 ha li phekolehe ka mocheso, ka hona thepa ea mochini e ntlafatsoa ke ts'ebetso e batang: e na le polasetiki e phahameng maemong a annealed, e ntle. plasticity ha serame se batla se thatafala, athe polasetiki e tlase nakong ea ho thatafala ha serame.E na le khanyetso e ntle ea kutu, e khona ho chesehela hantle, empa e na le ts'ebetso e mpe.E sebelisoa haholo-holo likarolong tse tlaase tse sebetsang ka mokelikeli kapa khase 'me e hloka sebopeho se phahameng le ho cheseha, joalo ka tanka ea oli, peterole kapa peipi ea lubricate, setshelo sa mokelikeli le likarolo tse ling tse tlaase tse entsoeng ka setšoantšo se tebileng.Lithupa tsa terata li sebelisoa ho etsa li-rivets.
Kopo:
Ka thepa e ntle e thibelang mafome, lishiti/likhoele tsa aluminium tse 3003 li loketse ho sebelisoa libakeng tse mongobo joalo ka lihatsetsi kapa li-conditioner ducts, likarolo tsa mochini, kapa ho paka kantle.
Li-coil tsa aluminium tsa 3003 li boetse li sebelisoa ka ho pharaletseng ho likepe / likepe, likoloi, likoloi le likopano tsa li-welding tse kenyang mollo, likepe tsa khatello ea mollo, thepa ea sehatsetsing, tora ea thelevishene, lisebelisoa tsa ho cheka, lisebelisoa tsa lipalangoang le tsa puisano, lisebelisoa tsa metsu, lihlomo tsa lipoleiti joalo-joalo.
Tshebetso:
1) Ho hanyetsa kutu e ntle le matla a itekanetseng.;
2) Ho cheseha ho hoholo, sebopeho, le machinability.
PRODUCTNAME | KHALA NOMA | MOHALE | BOTETE (MM) | WIDTH (MM) | LENGTH (MM) | KOPO |
3003 Aluminium Coil | 3003 | O,H12,H14,H16H18,H19,H22,H24,H26,H28,H32,H34 H36,H38 | 0.2-7.0 | 20-2200 | 600-6000 | Sekoahelo sa botlolo, sekoaelo sa botlolo ea seno, sekoaelo sa litlolo joalo-joalo |
Thepa ea Mechini
Litlhoko tsa thepa ea mochini bakeng sa sehlahisoa se kentsoeng (O temper) joalo ka ha ho boletsoe ho ASTM B209 le ASME SB209
Botenya (inch) | Kotulo Matla Min.(ksi) | Tensile Strength (ksi) | Elongation (%) Min. | Bend Diameter Factor, N | |
Min. | Max. | ||||
0.006 - 0.019 | 5.0 | 14.0 | 19.0 | 14 | 0 |
0.008 - 0.012 | 5.0 | 14.0 | 19.0 | 18 | 0 |
0.013 - 0.031 | 5.0 | 14.0 | 19.0 | 20 | 0 |
0.032 - 0.050 | 5.0 | 14.0 | 19.0 | 23 | 0 |
0.051 - 0.249 | 5.0 | 14.0 | 19.0 | 25 | 0 |
0.250 - 3.00 | 5.0 | 14.0 | 19.0 | 23 | - |
Litlhoko tsa thepa ea mochini bakeng sa mocheso o thata oa H12 (¼ ka thata) joalo ka ha ho boletsoe ho ASTM B209 le ASME SB209
Botenya (inch) | Kotulo Matla Min.(ksi) | Tensile Strength (ksi) | Elongation (%) Min. | Bend Diameter Factor, N | |
Min. | Max. | ||||
0.017 - 0.019 | 12.0 | 17.0 | 23.0 | 3 | 0 |
0.020 - 0.031 | 12.0 | 17.0 | 23.0 | 4 | 0 |
0.032 - 0.050 | 12.0 | 17.0 | 23.0 | 5 | 0 |
0.051 - 0.113 | 12.0 | 17.0 | 23.0 | 6 | 0 |
0.114 - 0.161 | 12.0 | 17.0 | 23.0 | 7 | 0 |
0.162 - 0.249 | 12.0 | 17.0 | 23.0 | 8 | 0 |
0.250 - 0.499 | 12.0 | 17.0 | 23.0 | 9 | - |
0.500 - 2.000 | 12.0 | 17.0 | 23.0 | 10 | - |
Litlhoko tsa thepa ea mochini bakeng sa khatello e thata ea H14 (½ ka thata) joalo ka ha ho boletsoe ho ASTM B209 le ASME SB209
Botenya (inch) | Kotulo Matla Min.(ksi) | Tensile Strength (ksi) | Elongation (%) Min. | Bend Diameter Factor, N | |
Min. | Max. | ||||
0.009 - 0.012 | 17.0 | 20.0 | 26.0 | 1 | 0 |
0.013 - 0.019 | 17.0 | 20.0 | 26.0 | 2 | 0 |
0.020 - 0.031 | 17.0 | 20.0 | 26.0 | 3 | 0 |
0.032 - 0.050 | 17.0 | 20.0 | 26.0 | 4 | 0 |
0.051 - 0.113 | 17.0 | 20.0 | 26.0 | 5 | 0 |
0.114 - 0.161 | 17.0 | 20.0 | 26.0 | 6 | 2 |
0.162 - 0.249 | 17.0 | 20.0 | 26.0 | 7 | 2 |
0.250 - 0.499 | 17.0 | 20.0 | 26.0 | 8 | - |
0.500 - 1.000 | 17.0 | 20.0 | 26.0 | 10 | - |
Lintho Tsa 'Mele
Thepa ea 'mele bakeng sa Alloy 3003
Thepa | Lintlha tsa 3003 |
Density, lb/in3 | 0.099 |
Modulus ea Elasticity, psi | 10.0 x 106 |
Coefficient of Thermal Katoloso, 68-212˚F, /˚F | 12.9 x 10-6 |
Thermal Conductivity, Btu/ft hr ˚F | 112 |
Mocheso o khethehileng, Btu/lb ˚F | 0.213 |
Motlakase Resistivity, Microohm-in | 1.374 |
LIMITI EA MOTSO OA K'hemik'hale (%)
Si | Fe | Cu | Mn | Mg | Cr | Ni | Zn | Ti | Ba bang | Kakaretso | Kakaretso |
0.6 | 0.7 | 0.05 - 0.2 | 1.0 - 1.50 | - | - | - | 0.1 | - | 0.05 | 0.15 | Mesala
|
Motsoako oa lik'hemik'hale ke boholo ba liperesente ntle le haeba bo bonts'itsoe joalo ka mefuta kapa bonyane.
Mohloli: Melao ea Aluminium le Lintlha-Mokhatlo oa Aluminium Association, Inc.
Tlhahisoleseding e hlahisoang e le tataiso bakeng sa litšupiso feela 'me ha ea rereloa ho sebelisoa bakeng sa moralo oa sehlahisoa kapa ts'ebeliso.
ASTMB209,EN573,EN485
ASTMB209-Tlhahiso ena e akaretsa aluminium le aluminium alloy alloy sheet, lakane e kopantsoeng le poleiti ka li-alloys tse fapaneng.
BS EN 573-Tlhaloso ena e akaretsa li-alloys tsa aluminium le aluminium - sebopeho sa lik'hemik'hale le mofuta oa lihlahisoa.
BS EN485-Tlhaloso ena e hlahisa thepa ea mochini ea aluminium e entsoeng ka aluminium e entsoeng ka letlapa la alloy, strip le poleiti bakeng sa lits'ebetso tse akaretsang tsa boenjiniere.
Lintlha tsa ho Paka : Sephutheloana se tloaelehileng sa ho romela thepa.
Aluminium Sheet ea ho paka e kopana le maemo a kantle ho naha.Filimi ea polasetiki le pampiri e sootho li ka koaheloa ka tlhoko ea bareki.mokotla oa mapolanka kapa pallet ea lehong e amoheloa ho sireletsa lihlahisoa ho senya nakong ea ho pepa.
Ho paka: Romella liphalete tsa mapolanka kantle ho naha, pampiri ea matsoho, moemeli oa anti-blushing. |
Boholo ba ka hare ba setshelo bo ka tlase: |
20ft GP: 5.8m(bolelele) x 2.13m(bophara) x 2.18m(hodimo) e ka bang 24-26CBM,23MTS |
40ft GP: 11.8m(bolelele) x 2.13m(bophara) x 2.18m(hodimo) e ka bang 54CBM,27MTS |
40ft HG: 11.8m(bolelele) x 2.13m(bophara) x 2.72m(hodimo) e ka bang 68CBM,27MTS |